If a single transaction has both positional and size changes, ensure we don't draw
any frames using the incorrect buffer size using the updated position. Wait for the correct
buffer size and then proceed.
Change-Id: I8e25f21f17e0936e66bb5053f85f8336c8464c7b
* Add a new binder transaction for applying a secondary color matrix
using RenderEngine. This stacks with the primary color matrix
(if set for a11y) to enable GPU-based display calibration.
Change-Id: I766455bfb5212e2dcc8ad0cb8ebdddbda87af732
Increase frame buffer surface buffers to 3. Call allocateBuffers
from the producer so that buffers are allocated. With out this,
BufferQueue implementation will only allocate 1 buffer
CRs-Fixed: 930504
@Buganizer: 26778657
Change-Id: Id0cadeb78957273d670d63f9956a09454b45eb69
- Collect dumpsys to an outfile file when triggered.
- Collect dumpsys before calling Prepare on hwc module in
each draw cycle. Recollect dumpsys if Commit goes through
successfully and replace former dumpsys with this.
- Wrap around if file size reaches appx 20 MB.
- Generate output file at /data/misc/display/dumpsys.txt
- Syntax:
adb shell dumpsys SurfaceFlinger --file [--no-limit]
--file : Ouput dumpsys to file
--no-limit : Do not wrap around, keep appending
Use same command to trigger start and end of dumping.
- Output format:
| start code | after commit? | time stamp | dump size | dump data |
CRs-Fixed: 947084
Change-Id: Ie520f51c69757aeec88b9400688a7f3271472349
- When rotation animation is disabled on secondary displays, remove
the screenshot surface from the secondary display list, without
this it would show up upside down frame on secondary.
- Mark IntOnly layers as invisible on secondary displays.
Change-Id: Ia859ee1c6ac7caa132c95e4f906bd2589e786fac
Crs-fixed: 949263
SurfaceFlinger uses two event-threads to support phase-offsets
for application and SurfaceFlinger itself. Extra thread may
cause scheduling issues and wake-up latency for either
SurfaceFlinger or Application, depending on scheduling, even
when running at higher priority as these threads have low-load
and qualify for task-packing.
Use single event-thread when phase offsets are same.
Debug runtime service call behavior change when same phase-offset:
1018 (set phase offset for Application): will change both
Application and SurfaceFlinger phase offsets.
1019 (set phase offset for SurfaceFlinger): Will be a no-op.
Change-Id: I2514b4ff6249e9bce3eb19f60b1dfe0de12b86d9
* QC media encoder appears to be incapable of switching between RGBA8888
buffers and NV12_ENCODEABLE dynamically. This requires that we switch
the entire stack to use the QC opaque format, or RGBA8888.
REF: CRACKLING-938
Change-Id: Ibd6a8faf8d268d3bfb4d61e4118a778ed82f1ab5
-1/+1 somewhat simplifies the values that can be generated by rotary
encoders, and rules out the possibility of batching and more nuanced
movement reporting.
So, we modify the device configuration to allow values other than -1 and
1 to be supported. In order to give the developer a sense of what these
values map to in terms of angular displacement, we also parse a
resolution configuration from the devices IDC file.
This will be specified as:
device.res = xxxx
of type float. If a value is not provided, a default res value of 0.0f
is used.
This patch also adds a per device scaling factor, which is used to
suitably modify the values reported (as well as the resolution) to tune
the input events generated and resulting UI according to the hardware.
This can be specified in the IDC file as:
device.scalingFactor = xxxx
of type float. If a scaling factor is not provided, a default of 1.0f
is used.
Bug: 22836852
Bug: 18707397
Change-Id: I13686f64de1b52d3f6c97b2587ae41e52d1db6e2
Move the ExSurfaceFlinger, ExLayer, etc., classes to this
repository, to avoid dependency accross projects with static
linking
The following commits are included in this:
commit 04f501b31f627e47ae540b5160b2f86b7adbd921
Author: Baldev Sahu <bsahu@codeaurora.org>
Date: Wed Nov 25 18:05:51 2015 +0530
display-fw: Properly initialise mIsGPUAllowedForProtected flag
- This flag need to be initialize to false when layer is
created.
Change-Id: Ie3df40ffc4240c33883f19ecbef6428f7c539b07
CRs-fixed: 942102
commit 09032188751356db295bc5467133ec484dc536cd
Author: Arun Kumar K.R <akumarkr@codeaurora.org>
Date: Tue Oct 20 10:22:51 2015 -0700
display-fw: Enable checking for INTERNAL_ONLY private flag
Check for INTERNAL_ONLY private flag and return correct values
from the function isIntOnly
Change-Id: I61b44f636412e0ad93e1b3ff18e4accdf90eeafe
CRs-fixed: 927880
commit f687ac25b3482b92da3c252d29b65e850cca3ce1
Author: Arun Kumar K.R <akumarkr@codeaurora.org>
Date: Thu Oct 15 16:37:11 2015 -0700
display-frameworks: Include libqdutils
only for target builds
Featurize including libqdutils for targets which uses QCOM_BSP,
helps in resolving compilation for emulator builds
Change-Id: I39639c3100eb20dd24d2a875bb0e9bc82d2b2d1f
commit 4ec765e01be506a8083980fc746a1737bbac4bf2
Author: Arun Kumar K.R <akumarkr@codeaurora.org>
Date: Wed Oct 7 18:33:34 2015 -0700
display-fw: Disable rotation animation on secondary displays
- Set the animating flag on layer during animation which is used
as hint to disable rotation animation on secondary displays.
- Set sys.disable_ext_animation to enable the feature
- Remove unused definitions in the extended hwc header
Change-Id: I7b72c7b605930ea189e047fec17ed18b17d46fdf
CRs-fixed: 922304
commit 6998bbdfd7af3126b64897b16b6961e84952601b
Author: Baldev Sahu <bsahu@codeaurora.org>
Date: Thu Jul 30 16:01:15 2015 +0530
display-frameworks: Extend support for MDP3
- Add support for HWC_BLIT
- Allow GPU to compose widevine level 3
Change-Id:I11e03ccd0842d019e85d0c29bc5b7be559fccbaa
commit 2fa7aa1684c0162b8226c4327c86c6eaf6b76101
Author: Manoj Kumar <manoj@codeaurora.org>
Date: Thu Aug 20 13:52:15 2015 -0700
display-frameworks: Override mOutputUsage with sink Usage flags
mOutputUsage flags contain default usage flags and doesnt reflect
sink usage flags. Override mOutputUsage with sink usage flags.
This change is needed to support WFD Secure usecase.
Change-Id: I14d8812049f635a8ebe6a944783e0ec7f8f80b1f
commit 09da768794c8c6acd786d73239ed5a739695b8cb
Author: Raj Kamal <rkamal@codeaurora.org>
Date: Mon Jul 20 10:46:27 2015 +0530
display-frameworks: Extend the classes defined in SF
Add support for custom classes ExSurfaceFlinger,
ExLayer, ExHWComposer and ExVirtualDisplaySurface
Change-Id: Iab8c4835faaad9b436bbd34d38702741eb0cf12d
Change-Id: Ie400c94ccc77fc379ffa256af03a9e42ba5decaa
This error can be seen for the following use case
1. Connect HDMI display
2. Dump the SurfaceFlinger state
The problem here is that HWComposer would have processed the display
connection event via the hotplug mechanism and considers that the
external display is connected. However, SurfaceFlinger has not
updated its internal state (mDisplays) since it will be waiting for
the mStateLock to be release by the dump function. As a result, when
the dump function invokes the getLayerSortedByZForHwcDisplay for the
external display, we will end up seeing the error log message because
SurfaceFlingers internal state has not yet been updated.
We can move this to ALOGW since it is a non-fatal/recoverable state.
CRs-Fixed: 914173
Change-Id: Ib0ba359ecd894dd463417ba57ba1f72c07b5833e
Reduce transparent region from a layer only if the transparent
region has valid intersection with the layer. Otherwise, reducing
a transparent region lying completely outside of the layer leads to
invalid sourcecrop values for the layer.
Change-Id: Iee9ba53a8072c21c9ba8a6d58cb14ca30f8600ba
CRs-Fixed: 620973
Compute crop and display frame for GPU composition also
in the same way it's done for HWC and compute vertices
and texture coordinates for GPU composition. This avoids
pixel shifts in output of GPU composition & overlays.
Change-Id: I0d31b1e4a81049fff72109d1a210e7cbd945cfe9
[root cause ] framebuffer surface is in the same process of surface flinger
[changes ] call IGraphicBufferProducer::allocateBuffers on producer inside the DisplayDevice constructor to force-allocate all three buffers.
[side effects] none
[self test ]<tshark, enter and exit mainmenu>: ok
[reviewers ] zhongjun.chen
[change_type ] AOB --> google_original
[tag_product ] common
Change-Id: Ideb75d3aa1ed23b2fa4d263a120ea3ca39d01361
This change is porting of below commits related to MDP3
In MDP3 we are using the widevine level3 for secure content
display. And this should applicable only for primary display
not for screen shot or screen recording
- CRs-Fixed: 595469
- Change-Id: I99be2d81287ab746d5c4a2375c3106c59e61a8fc
Change-Id: Ie7ac95e1c03eb7ad6f71098ecf09a1e25e69760f
This is special solution only for emerald branch.
Changes including new const char* value/interface for sensor physical data. Sensor service and manager does not take care of content, structure or other
details of string. Sensor HAL is taking care of parsing data from string and setting values to Sensor HW.
Change-Id: I3abc3ddc7c6adc4b32a40b9a43f2a94c5af7b2b0
Signed-off-by: Ben Fennema <fennema@google.com>
SurfaceFlinger shouldn't be limited to little cores exclusively, as the
binder threads should be placed on big cores when they are in the
critical path for a RenderThread.
bug 25745866
Change-Id: I9fb65f6d951733f91b4735ff27018411b58b2bfb
Blur layer need to capture screen shot to create to blur
effect. Hence need to take care any user defined orientation
as well.
Change-Id: I1c0478810d12661edf2586293bbed342a5b4dc7e
Dedupe rotation calculation code and make rotation a statically
available property in the DisplayDevice
Change-Id: Ic517ab0d2c05026cd6fa46d664aab7926be17b62
This patch works in addition to the following commit
re-implementing ro.sf.hwrotation:
7d283431ef
When using values of 90 and 270 for ro.sf.hwrotation the
LCD width and height also need to be swapped to display properly.
Change-Id: I2874fdb8f8d8b855df6d62d338c9a22360491973
NOTE: This patch does not fix the initial startup of bootanimation
* Previously HAL orientation sensor would always be replaced if the HAL
did not provide a rotation vector sensor as well. Practically no HAL
does, so the virtual sensor would always replace it.
* Add the virtual sensor only if the HAL does not provide it.
Change-Id: I50ad2cd6c60b53eddc4c6854997ec2e3dbff0d1a
* In KitKat and on most Samsung devices, the orientation sensor is
not getting registered, and makes the compass non-working in a lot
of apps. This patch enables the sensor for such devices.
Change-Id: I0ebba72ec4aa2cfa02c21a6daff0c356c6793fd0
(cherry picked from commit 98fa6f1152da759ef3eaf36cb16e0aaf2013376a)
The sensors API introduced a new flush() method that older binaries
won't have. For those, replace the firstFlush invocation with a
setDelay call since a lot of implementations interpreted that as
the initialization step.
We also don't want any kind of call to flush() to happen when it
isn't there, since it'll either hit a random OEM extension or
a memory address we really don't want to execute.
Change-Id: I26ce923fe385751fed7d1c483a53c074249f0620
sensorservice: Set the rate for pre-1.1 HALs _after_ activation
We want to be sure these are applied in the same sequence they
used to be...
Change-Id: Ied2ba08ed3c4bed3a80bac6ab5471fcea9ba2c09
If triple framebuffers are enabled, the number of acquired
buffers isn't increased by default. Set the count to one less
than the max buffers to make sure all three buffers come into
play.
Change-Id: I8fae1b5564fbea598e415a86b0a21c3449c92d87
Reserve HWC for VDS for WFD use case. During WFD usecase, sink usage
will contain GRALLOC_USAGE_PRIVATE_WFD flag.
When HWC is avoided, all virtual displays are composed using GLES.
This means that GLES composes directly into the sink buffer and
signals the consumer. Furthermore, it is expected that any color
conversion will be handled on the consumer side.
CRs-Fixed: 908380
Change-Id: I93ff54c79ece788b6caf3f4172835d8ac1362f62
Initial sensor flush at subscription is a mechanism to avoid sensors
to get stale samples before subscription happens. However, there is a
slight chance that a most recent sample will be lost during the flush
process. This is OK for continuous sensors but problematic in
on-change sensor as on-change event does not come continuously and
a lost event can cause inconsistent state in client. Flush at
subscription of on-change sensor is disabled in this CL to avoid new
important on-change event to be discarded during the initial flush
process.
Bugs: b/24647069
b/25241873
b/24804819
Change-Id: Ibda099c6b9f5fb6e200f13cf13a850b0026e9e7c
- Add support to set animating layer for HWCLayers
- After hwc_prepare, dont override the compType of a layer to
HWC_FRAMEBUFFER if its for non-primary displays
Change-Id: Iac462778ce5fb9016290846146e62f80dcfafd5c
CRs-fixed: 922304
* The visible pointer icon when hovering or drawing with the stylus is
quite annoying when trying to actually draw with it. Turn it off by
default and add an option to turn it on.
Forward Port from CM-11.0
Change-Id: Ie4e9e6bcc48803b195d1615d83d6e36d663cc33a
