When a surface is removed from the screen while it holds a "freeze lock", the
release of that lock happens in the destructor as a "safety net". However, it
doesn't trigger an update at that point.
Make sure that "freeze locks" are released from the transaction at the point
a surface is removed from the screen (if it's not on screen, it shouldn't
prevent the screen to redraw, and therefore cannot hold a freeze lock).
The refresh corresponding to that transaction will pick it up as soon as possible.
this was introduced by a recent change. when we try to figure out the size of
the yuv->rgb temporary buffer, the output resolution has not been computed yet
and an invalid buffer size is used. most of the time the allocation fails
and the system reverts to "standard" GL will uses onle the Y plane.
the allocation of the temporary buffer is moved to onDraw(), the first
time it is called, by that time, the window is positioned properly.
always rescale videos to their target size using copybit during yuv->rgb
conversion. this improves performance of the GPU pass and doesn't require
linear filtering to be enabled. Also always use 16-bits buffers.
the average processing time for 720p dropped from ~50ms to ~30ms
The image buffer used by glTexImage2d() would be uninitialized when no copybit engine
can be found.
We now always initialize images, since the abscence of copybit is not necessarily fatal.
There was bug in the logic that calculated the relative timeout, the start time was
reset each time an event was received, which caused the timeout to never occur if
an application was constantly redrawing.
Now we always check for a timeout when we come back from the waitEvent() and
process the "anti-freeze" if needed, regardless of whether an event was received.
since we're using the GPU for composition, don't use a texture for dimming,
instead simply use an alpha-blended quad.
also workaround what looks like a GL driver bug by calling glFinish() before
glReadPixels().
2206097: Broken suggestions while composing message
2166583: Color artifacts with MDP dithering
2261119: Passion transition animations are rough
2216759: Screen flicker when dropdown list in background window shows or hides
This is part of enabling GPU composition instead of using the MDP. This change
is dependent on another change in the vendor project.
Specifically this change disables the use of EGLImageKHR for s/w buffers
for cache coherency reasons. memcpy is used instead.
This builds on the EGLImage solution. We simply use copybit to convert from the
YUV frame into an EGLImage created for that purpose and proceed with the
regular EGLImage code.
We need to do this because "regular" GL doesn't support YUV textures.
We could improve upon this by detecting exacly what the GL supports and bypass
this extra step if not required, but we'll do this later if needed.
we lost the concept of vertical stride when moving video playback to EGLImage.
Here we bring it back in a somewhat hacky-way that will work only for the
softgl/mdp backend.
add a way to convert a mapped "pushbuffer" buffer to a gralloc handle
which then can be safely used by surfaceflinger, without including
gralloc_priv.h
Temporarily make a function public that doesn't need to be. When
host gcc-4.0.3 is gone from the build servers we can undo this.
(Cherry-picked from eclair-mr2.)
Use EGLImageKHR instead of copybit directly.
We now have the basis to use streaming YUV textures (well, in fact
we already are). When/if we use the GPU instead of the MDP we'll
need to make sure it supports the appropriate YUV format.
Also make sure we compile if EGL_ANDROID_image_native_buffer is not supported
Instead of using glTex{Sub}Image2D() to refresh the textures, we're using an EGLImageKHR object
backed up by a gralloc buffer. The data is updated using memcpy(). This is faster than
glTex{Sub}Image2D() because the texture is not swizzled. It also uses less memory because
EGLImageKHW is not limited to power-of-two dimensions.
When switching rapidily orientation back and forth, surfaces end-up
acquiring the freeze-lock when the first orientation change happens,
but never release it because by the time the 2nd orientation change
comes in, the surface size is back to its original size and
doesn't appear to have resized.
we now always release the freeze-lock when we receive a buffer of the
expected size.
This also fixes [2152536] ANR in browser
When SF is enqueuing buffers faster than SF dequeues them.
The update flag in SF is not counted and under some situations SF will only
dequeue the first buffer. The state at this point is not technically
corrupted, it's valid, but just delayed by one buffer.
In the case of the Browser ANR, because the last enqueued buffer was delayed
the resizing of the current buffer couldn't happen.
The system would always fall back onto its feet if anything -else- in
tried to draw, because the "late" buffer would be picked up then.
A window is created and the browser is about to render into it the
very first time, at that point it does an IPC to SF to request a new
buffer. Meanwhile, the window manager removes that window from the
list and the shared memory block it uses is marked as invalid.
However, at that point, another window is created and is given the
same index (that just go freed), but a different identity and resets
the "invalid" bit in the shared block. When we go back to the buffer
allocation code, we're stuck because the surface we're allocating for
is gone and we don't detect it's invalid because the invalid bit has
been reset.
It is not sufficient to check for the invalid bit, I should
also check that identities match.
When EGLImage extension is not available, SurfaceFlinger will fallback to using
glTexImage2D and glTexSubImage2D instead, which requires 50% more memory and an
extra copy. However this code path has never been exercised and had some bugs
which this patch fix.
Mainly the scale factor wasn't computed right when falling back on glDrawElements.
We also fallback to this mode of operation if a buffer doesn't have the adequate
usage bits for EGLImage usage.
This changes only code that is currently not executed. Some refactoring was needed to
keep the change clean. This doesn't change anything functionaly.
The ANR is caused by SurfaceFlinger waiting for buffers of a removed surface to become availlable.
When it is removed from the current list, a Surface is marked as NO_INIT, which causes SF to return
immediately in the above case. For some reason, the surface here wasn't marked as NO_INIT.
This change makes the code more robust by always (irregadless or errors) setting the NO_INIT status
in all code paths where a surface is removed from the list.
Additionaly added more information in the logs, should this happen again.
We were emitting GL commands, calling composition complete and releasing clients
without ever calling eglSwapBuffers(), which is completely wrong on non-direct
renders. This could cause transient drawing artifacts when unfreezing the
screen (upon orientaion change for instance) and could also block the clients
for ever as they are waiting for their previous buffer to be rendered.
This appears to fix the sim-eng build on the gDapper build machines.
Basic problem is that LayerBuffer::OverlaySource has a constructor that
calls SurfaceFlinger.signalEvent(). SurfaceFlinger lists LayerBuffer
as a friend, but that's not enough to convince gcc that the embedded
OverlaySource class is also a friend. I don't see a way to make them
friendly, so I marked signalEvent() as public.
a new method, compostionComplete() is added to the framebuffer hal, it is used by surfaceflinger to signal the driver that the composition is complete, BEFORE it releases its client. This gives a chance to the driver to
