this hack was used for gpus that don't support cached buffers
for s/w clients. currently we have no gpu with this issue.
this removes quite a bit of complexity.
Change-Id: I72564669f124f92805030e61983711f61c76b6d9
We now limit the size of the surface to the maximum size supported by the GPU.
On Nexus One this will 2048 -- it could be different on other devices.
Surface creation fails if the limit is exceeded.
Change-Id: I9ecfc2e9c58c9e283782b61ebfc6b590f71df785
2206097: Broken suggestions while composing message
2166583: Color artifacts with MDP dithering
2261119: Passion transition animations are rough
2216759: Screen flicker when dropdown list in background window shows or hides
This is part of enabling GPU composition instead of using the MDP. This change
is dependent on another change in the vendor project.
Specifically this change disables the use of EGLImageKHR for s/w buffers
for cache coherency reasons. memcpy is used instead.
Use EGLImageKHR instead of copybit directly.
We now have the basis to use streaming YUV textures (well, in fact
we already are). When/if we use the GPU instead of the MDP we'll
need to make sure it supports the appropriate YUV format.
Also make sure we compile if EGL_ANDROID_image_native_buffer is not supported
a new method, compostionComplete() is added to the framebuffer hal, it is used by surfaceflinger to signal the driver that the composition is complete, BEFORE it releases its client. This gives a chance to the driver to
Rewrote SurfaceFlinger's buffer management from the ground-up.
The design now support an arbitrary number of buffers per surface, however the current implementation is limited to four. Currently only 2 buffers are used in practice.
The main new feature is to be able to dequeue all buffers at once (very important when there are only two).
A client can dequeue all buffers until there are none available, it can lock all buffers except the last one that is used for composition. The client will block then, until a new buffer is enqueued.
The current implementation requires that buffers are locked in the same order they are dequeued and enqueued in the same order they are locked. Only one buffer can be locked at a time.
eg. Allowed sequence: DQ, DQ, LOCK, Q, LOCK, Q
eg. Forbidden sequence: DQ, DQ, LOCK, LOCK, Q, Q
Merge commit '1521cd6e657ba4efa9382ab73d3cbba3bdf50ead'
* commit '1521cd6e657ba4efa9382ab73d3cbba3bdf50ead':
Reset the mDpiX and mDpiY values when qemu.sf.lcd_density is defined.
ro.sf.lcd_density is usually defined in the build.prop file which is parsed by init
before anything else. Since its name begins with "ro.", this property is write-once
and cannot later be modified, e.g. in /system/etc/init.goldfish.sh.
In other words, you cannot use "emulator -prop ro.sf.lcd_density=<value>", since
it is impossible to override the value defined in build.prop
This patch modifies the system to recognize "qemu.sf.lcd_density" as an override
value, which can be set with "emulator -prop qemu.sf.lcd_density=<value>", forcing
a specific density.
A later patch will allow the emulator to automatically set this property depending
on AVD hardware configuration settings.
ANDROID_swap_rectangle allows to specify the rectangle affected by eglSwapBuffers(), anything outside of this rectangle is unchanged. in particular EGL_BUFFER_DESTROYED only applies to that rectangle. This extension as well as EGL_BUFFER_PRESERVED allow major optimizations on surfaceflinger, which can redraw only the dirty area during compositing.
However, ANDROID_swap_rectangle allows further optimizations in EGL by reducing the amount of copy-back needed. ANDROID_swap_rectangle is particularily important for software implementations.
- Currently the lock/unlock path is naive and is done for each drawing operation (glDrawElements and glDrawArrays). this should be improved eventually.
- factor all the lock/unlock code in SurfaceBuffer.
- fixed "showupdate" so it works even when we don't have preserving eglSwapBuffers().
- improved the situation with the dirty-region and fixed a problem that caused GL apps to not update.
- make use of LightRefBase() where needed, instead of duplicating its implementation
- add LightRefBase::getStrongCount()
- renamed EGLNativeWindowSurface.cpp to FramebufferNativeWindow.cpp
- disabled copybits test, since it clashes with the new gralloc api
- Camera/Video will be fixed later when we rework the overlay apis
